Standards

물리적 시험 및 시험치 분석을 통한 평가 표준에

ASTM D1002

Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)

This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.


ASTM D1654

Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrustions and Panels

This specification describes test procedures and performance requirements for high performance organic coatings applied to aluminum extrusions and panels for architectural products.


ASTM D1876

Standard Test Method for Peel Resistance of Adhesives (T-Peel Test)

This test method is primarily intended for determining the relative peel resistance of adhesive bonds between flexible adherents by means of a T-type specimen.


ASTM D2244

Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates

This practice covers the calculation, from instrumentally measured color coordinates based on daylight illumination, of color tolerances and small color differences between opaque specimens such as painted panels, plastic plaques, or textile swatches.


ASTM D3164/M

Standard Test Method for Strength Properties of Adhesively Bonded Plastic Lap-Shear Sandwich Joints in Shear by Tension Loading

This standard covers a test method for strength properties of adhesively bonded plastic lap-shear sandwich joints in shear by tension loading.


ASTM D3330

Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape

Standard test method for peel adhesion of pressure-sensitive tape.


ASTM D3528

Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading

This test method covers the determination of the tensile shear strengths of adhesives for bonding metals when tested in an essentially peel-free standard specimen that develops adhesive stress distribution representative of that developed in a typical low-peel production-type structural joint.


ASTM D412

Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers - Tension

These test methods cover procedures used to evaluate the tensile (tension) properties of vulcanized thermoset rubbers and thermoplastic elastomers.


ASTM D4214

Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films

These test methods cover the evaluation of the degree of chalking on white or tinted exterior paint films.


ASTM D5034

Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)

This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics.


ASTM D5035

Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method)

This test method covers raveled strip and cut strip test procedures for determining the breaking force and elongation of most textile fabrics.


ASTM D523

Standard Test Method for Specular Gloss

This test method covers the measurement of the specular gloss of nonmetallic specimens for glossmeter geometries of 60, 20, and 85°.


ASTM D624

Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers

This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.


ASTM D638

Standard Test Method for Tensile Properties of Plastics

This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.


ASTM D660

Standard Test Method for Evaluating Degree of Checking of Exterior Paints

Since checking is not easily recognizable, this test method is intended to provide, through definition and illustrations, a means of evaluating the degree of this film failure.


ASTM D661

Standard Test Method for Evaluating Degree of Cracking of Exterior Paints

This test method covers the evaluation of the degree of cracking of exterior paints by comparison with photographic standards.


ASTM D662

Standard Test Method for Evaluating Degree of Erosion of Exterior Paints

This test method covers the evaluation of the degree of erosion of exterior paints by comparison with photographic standards.


ASTM D6862

Standard Test Method for 90 Degree Peel Resistance of Adhesives

This test method covers the determination of the resistance-to-peel strength of an adhesive bond between one rigid adherend and one flexible adherend when tested at an angle of approximately 90 degrees under specified conditions of preparation and testing.


ASTM D7003

Standard Test Method for Strip Tensile Properties of Reinforced Geomembranes

This test method is used to measure the strip tensile properties of reinforced geomembranes.


ASTM D7004

Standard Test Method for Grab Tensile Properties of Reinforced Geomembranes

This test method is used to measure the grab tensile properties of reinforced geomembranes.


ASTM D7087

Standard Test Method for An Imaging Technique to Measure Rust Creepage at Scribe on Coated Test Panels Subjected to Corrosive Environments

This test method covers the measurement of rust creepage area from a scribe line on painted/coated flat test panels after exposure to corrosive environments.


ASTM D714

Standard Test Method for Evaluating Degree of Blistering of Paints

This test method employs photographic reference standards to evaluate the degree of blistering that may develop when paint systems are subjected to conditions which will cause blistering.


ASTM D751

Standard Test Methods for Coated Fabrics

These test methods cover, but are not limited to, rubber-coated fabrics; that is, tarpaulins, rainwear, and similar products


ASTM D772

Standard Test Method for Evaluating Degree of Flaking (Scaling) of Exterior Paints

This test method covers the evaluation of the degree of flaking (scaling) of exterior paints by comparison with photographic standards.


ASTM D882

Standard Test Method for Tensile Properties of Thin Plastic Sheeting

This test method covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness).


ISO 527

Plastics - Determination of Tensile Properties


SAE J1523

Metal to Metal Overlap Shear Strength Test for Automotive Type Adhesives, Recommended Practice

This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives.


Looking for a specific test standard? Search entire listing of all standards.

 

자원

연락하기

  1.  

Q-Lab Phone Numbers

USA: +1-440-835-8700
Florida & Arizona 시험 서비스: +1-305-245-5600
UK/Europe: +44-1204-861616
Germany: +49-681-857470
China: +86-21-5879-7970

 
View Full Site